AnaSCI - Fitness Evolved

Buy Needles and Syringes with NO PRESCRIPTION   Synthetek Muscle Building And Fat Loss Products   Cheap Pure Supplements

©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2019

   
  Synthetek Syntherol  
   
   
   
Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products


User CP FAQ Members List Calendar New Posts Quick Links Log Out

AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved


        
        
        
        
        

Automatic Translations (Powered by Yandex):
Albanian Belarusian Catalan Czech Danish Dutch English Estonian Finnish French German Greek Hungarian Italian Latvian Lithuanian Macedonian Norwegian Portuguese Russian Slovak Slovenian Spanish Swedish Turkish Ukrainian

Go Back   Anabolic Steroids Discussion and Bodybuilding Forum > Anabolic Science Section > Anabolic Science Forum

Reply
 
LinkBack Thread Tools Display Modes
50ml Equipoise 200mg/ml
Old
  (#1)
AnaSCI VET
 
powders101's Avatar
 
Offline
Posts: 1,556
Join Date: Sep 2007
Location: The LAB
50ml Equipoise 200mg/ml - 09-27-2011, 12:49 PM

Here's a recipe for making 50ml of 200mg/ml EQ (Boldenone Undeclyanate).
By: Kitchen Chemist

First thing first, Clean off area you are workin on with rubbing alchol and a cloth. Then go wash hands with antibacterial soap. Set up all ingredients needed, for this experiment it'll be the following:

10g Boldenone Undeclynate "Powder"
7.5ml of Benzyl Benzoate
2.5ml of benzyl alcohol
32ml of your favourite Oil
20CC syringe
12CC syringe
2 18ga needles, 1 25ga needle
.45 Sterile whatman filter
50ml Sterile Vial
50ml Vial
Electric Scale
Rubbing Alchol/Paper Towels

Now that all materials are in place, take out scale (i like to calibrate it every use) and put on unsterile 50ml vial on scale and zero out.

Draw up 12ml of Eq using 12ml syringe, make sure there are no airbubbles and plunger is exactly in line with 12ml hatch mark. Now slowly squirt eq into vial until scale says 10.0 grams. For me this is usually exactly 10ml so 1g has 1 mL displacement. Also add the 7.5ml of bb and 2.5ml of ba

Now add 30 of the 32ml of oil into the vial to make total volume of oil/ba/bb/hormone to be 50 mL. Leave the 2ml of oil in syringe for later use. Put rubber stopper into vial aswell as one of the 18ga needles. Boil a pot of hot water and then remove from heat and put vial into pot for 10 minutes, take out after 5 to shake and put back in.

I have a crimper so i crimp another seal on the vial but you could also duct tape it on so that rubber stopper doesn't come out when upside down when you're drawing oil out of vial.

Now take out sterile 50ml vial and wipe stopper with rubbing alchol. Put 18ga needle and 25ga needle through stopper, and attach whatman filter to the 18ga needle stuck in vial.

Once you've filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter.

Now put vial in oven at 200 degrees F, and bake for 15 minutes. Some repeat this step more than once but i never have and not had a problem.


Disclaimer: The articles and conversions posted are for entertainment and informational purposes only - experiment at you own risk.
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 04:20 AM.



Content Relevant URLs by vBSEO 3.6.0
Copyright © 2003-2019 AnaSCI.org. All rights reserved.