AnaSCI - Fitness Evolved

Buy Needles and Syringes with NO PRESCRIPTION   Synthetek Muscle Building And Fat Loss Products   Cheap Pure Supplements

©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2019

   
  Synthetek Syntherol  
   
   
   
Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products


User CP FAQ Members List Calendar New Posts Quick Links Log Out

AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved


        
        
        
        
        

Automatic Translations (Powered by Yandex):
Albanian Belarusian Catalan Czech Danish Dutch English Estonian Finnish French German Greek Hungarian Italian Latvian Lithuanian Macedonian Norwegian Portuguese Russian Slovak Slovenian Spanish Swedish Turkish Ukrainian

Go Back   Anabolic Steroids Discussion and Bodybuilding Forum > Anabolic Science Section > Anabolic Science Forum

Reply
 
LinkBack Thread Tools Display Modes
injection question
Old
  (#1)
AnaSCI MEMBER
 
Tainter's Avatar
 
Offline
Posts: 57
Join Date: Feb 2005
injection question - 02-21-2005, 12:59 AM

i am having difficulty drawing juice from the vial. It took me about 5 minutes. It was pulling up mostly air, then, turning the vial upside down slowly filled. Any easier way? I am using a 23 guage .
   
Reply With Quote
Old
  (#2)
wolfyEVH
Guest
 
Posts: n/a
02-21-2005, 01:02 AM

I'd use a 22 gauge myself......are you injecting air into the vial first???? this creates a vaccum and replaces what you are taking out of the vial. So if you are gonna draw up 1cc of gear, first draw up 1cc of air, then insert into the vial, inject all the air, and the gear should suck up pretty good.
   
Reply With Quote
Old
  (#3)
AnaSCI MEMBER
 
Tainter's Avatar
 
Offline
Posts: 57
Join Date: Feb 2005
02-21-2005, 01:06 AM

ok, i'll try it thursday. After pulling out of the test and going into the deca, i ran into the same problem. should i pull air again even with a cc of test in there?
   
Reply With Quote
Old
  (#4)
wolfyEVH
Guest
 
Posts: n/a
02-21-2005, 01:10 AM

Quote:
Originally Posted by Tainter
ok, i'll try it thursday. After pulling out of the test and going into the deca, i ran into the same problem. should i pull air again even with a cc of test in there?

yes, its kind of difficult to master, but you'll learn
   
Reply With Quote
Old
  (#5)
AnaSCI MEMBER
 
Tainter's Avatar
 
Offline
Posts: 57
Join Date: Feb 2005
02-21-2005, 01:16 AM

thanks bro
   
Reply With Quote
Old
  (#6)
AnaSCI MEMBER
 
Tainter's Avatar
 
Offline
Posts: 57
Join Date: Feb 2005
02-21-2005, 01:31 AM

what mistake ?
   
Reply With Quote
Old
  (#7)
pincrusher
Guest
 
Posts: n/a
02-22-2005, 09:07 AM

23 guage pinz are pretty small to be using for withdrawing product from vials. i use 18g or 20g at the smallest because when i go smaller than those i tend to pull up to much air and get alot of small bubbles in the syringe.
try ordering a box of 20g pinz from gearboxinc or getpinz and use them to withdraw the product then switch to the 23g for injecting. this will make the injection go easier also if you are currently using the same pin for drawing up product and injecting.
   
Reply With Quote
Old
  (#8)
tee
AnaSCI VET
 
tee's Avatar
 
Offline
Posts: 4,130
Join Date: Feb 2004
Location: USA
02-22-2005, 10:32 AM

I agree with Pin 100% unless you have a 50ml jug of gear. If you use an 18g or 20g pin, you'll have no rubber left on top by the time you get towards the lower 1/2 of the bottle. 50ml jugs dont seem to be that common nowadays, but if you have them, use a 21 or 22g pin.
   
Reply With Quote
Old
  (#9)
Steroid Nazi
 
DragonRider's Avatar
 
Offline
Posts: 3,717
Join Date: Jan 2004
Location: The shadows of your mind
02-22-2005, 06:37 PM

Quote:
Originally Posted by tee
I agree with Pin 100% unless you have a 50ml jug of gear. If you use an 18g or 20g pin, you'll have no rubber left on top by the time you get towards the lower 1/2 of the bottle. 50ml jugs dont seem to be that common nowadays, but if you have them, use a 21 or 22g pin.
I buy extra stoppers just for this purpose. When they get to the point that I'm afraid rubber might start falling into my vial, I replace the stopper.


Disclaimer: Anasci.org and DragonRider do not promote the use of anabolic steroids without a doctor's prescription. The information we share is for entertainment purposes only.

"NO STEROIDS FOR YOU!"
   
Reply With Quote
Old
  (#10)
AnaSCI MEMBER
 
BigTex's Avatar
 
Offline
Posts: 48
Join Date: Feb 2005
02-22-2005, 06:40 PM

I draw with a 20g 1" pin then change to a 22g 1 1/2" for injection. Seems to work well for me.
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 06:32 AM.



Content Relevant URLs by vBSEO 3.6.0
Copyright © 2003-2019 AnaSCI.org. All rights reserved.