AnaSCI - Fitness Evolved

Buy Needles and Syringes with NO PRESCRIPTION   Synthetek Muscle Building And Fat Loss Products   Cheap Pure Supplements

©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2019

   
  Synthetek Syntherol  
   
   
   
Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products


User CP FAQ Members List Calendar New Posts Quick Links Log Out

AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved


        
        
        
        
        

Automatic Translations (Powered by Yandex):
Albanian Belarusian Catalan Czech Danish Dutch English Estonian Finnish French German Greek Hungarian Italian Latvian Lithuanian Macedonian Norwegian Portuguese Russian Slovak Slovenian Spanish Swedish Turkish Ukrainian

Go Back   Anabolic Steroids Discussion and Bodybuilding Forum > Anabolic Science Section > Anabolic Science Forum

Reply
 
LinkBack Thread Tools Display Modes
High Mg per ML Roids, What you need to know
Old
  (#1)
tee
AnaSCI VET
 
tee's Avatar
 
Offline
Posts: 4,130
Join Date: Feb 2004
Location: USA
High Mg per ML Roids, What you need to know - 07-05-2005, 08:29 PM

High Mg per ML Roids, What you need to know

--------------------------------------------------------------------------------

1. Most hormones have a pretty low solubility in oil.
2. The primary ways to increase solubility are to
A) add solvent (BA or EA).
B) Add an ester to the hormone. The longer the ester the more hormone will fit in the oil at a certain mg per ml ratio. Conversely, the weight of the ester is also factored in the total mg per ml ratio, so while you can fit more hormone in, you are getting less actual hormone than the mg amount implies.

Here are some examples:

Ester actual mg/100mg dose
test no ester 100
tren acetate 87
test prop 83
test enanth 72
test cyp 70
test undecan 63
nand phenyl 67
nand deca 64

This means that if your test cyp says 200 mgs per ml you get an actual 140 mgs of test. The rest of the weight is the weight of the ester. If that sounds like a bad deal you need to understand that test no ester is VERY insoluble in oil without going to very high mg per ml solvent concentrations.

This brings up the next point; PAIN!

Why do some shots hurt? There are two primary reasons. One, the solvent ratio is too high. Anything over about 10% starts to hurt. BA and EA are VERY inflammatory to the tissues. Thatís why you want ONLY enough to help your oil hold more gear but not so much that it causes inflammation.

The second reason is that the gear crystallizes in the depot. This is precisely why water-based suspensions feel like hammer blows. The water is absorbed FAST, leaving the gear to crystallize in the tissues = PAIN.
Even gear in oil can do this, here is how it works. If you use a low ester weight attached to your gear and make the mg per ml ratio SIGNIFICANTLY higher than the oil will hold on it's own, what happens is the body absorbs the solvent faster than the oil/gear and the gear falls out of the solution and crystallizes in the depot and WHAM, it hurts like hell. An optimum solution has just enough solvent to get more gear into solution than you could otherwise, but not so much that what I just stated happens. When the ratios are correct the gear holds in the solution UNTIL the whole depot is absorbed and very little or no pain is felt. Just to end this misconception once and for all IT IS NOT THE VOLUME OF THE OIL THAT CAUSES THE PAIN, IT IS ONE OF THE CONDITIONS STATED ABOVE. You can shoot 5 cc's of sterile oil and never know you took a shot. It IS NOT HOW MUCH OIL YOU SHOOT! So why does everyone search for super high mg per ml ratio gear like it's the damn holy grail???

What is too high? Well the length of the ester is really what determines that but most of us here know the gear that hurts and know we know why. All tests over 250 mgs per ml hurt, and actually most of the 250 mg tests hurt too. SOOOO many people want there tren at 150-200 mgs per ml. Tren acetate should be at about what?? 75 mgs per ml. That is why all the kits are
designed this way. Do you really think it's cheaper for the kit producers to add MORE oil to their kits instead of less? One other quick note. Oil is used
because it SLOWS absorption. THIS IS PRECISELY WHAT YOU WANT IN A STEROID SHOT! Less oil does not promote the steady state hormone levels achieved with more oil
   
Reply With Quote
Old
  (#2)
AnaSCI's Ivan Drago
 
Offline
Posts: 534
Join Date: Apr 2005
07-05-2005, 08:38 PM

makes alot of sense, thx. The reason I prefer high mg/ml doses is b/c I run out of room to shoot it! 250mg/ml Deca is more practical for me for that reason.
   
Reply With Quote
Old
  (#3)
Banned
 
KILLA's Avatar
 
Offline
Posts: 401
Join Date: Feb 2005
07-05-2005, 09:09 PM

I wish they could come out with a "Test 1000".
   
Reply With Quote
Old
  (#4)
AnaSCI's Ivan Drago
 
Offline
Posts: 534
Join Date: Apr 2005
07-05-2005, 09:13 PM

Yeah that would be nice... I wouldn't be able to sit or lay down for a week, then it would be time for the next shot lol
   
Reply With Quote
Old
  (#5)
AnaSCI SENIOR
 
Freejay's Avatar
 
Offline
Posts: 877
Join Date: Feb 2005
Location: Michigan
07-05-2005, 10:26 PM

Great post T!


American Bad Ass!! :rockon:
   
Reply With Quote
Old
  (#6)
pincrusher
Guest
 
Posts: n/a
07-06-2005, 07:52 AM

Quote:
Originally Posted by SuperFly
I wish they could come out with a "Test 1000".
the highest i ever went with test was a 500mg/ml product from black label, and it hurt like hell. after that i said fruck it to high mg/ml dosages and just worked on finding more injection sites for all my shots.
   
Reply With Quote
Old
  (#7)
AnaSCI SENIOR
 
STEELADDICTION's Avatar
 
Offline
Posts: 735
Join Date: Apr 2004
07-06-2005, 06:05 PM

Great post TEE.


STEELADDICTION is presenting fictitious opinions and does in no way encourage, use nor condone the use of any illegal substances or the use of legal substances in an illegal conduct.
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 10:38 AM.



Content Relevant URLs by vBSEO 3.6.0
Copyright © 2003-2019 AnaSCI.org. All rights reserved.