I am going to post this as pretty basic mainly outlined around the safety and sterility of your brew.
Not getting into recipes cause there are tons of powder calculator sites around for oil powder solvent .
I use USP castor oil, and Sterile vials and USP solvents, please don't ask me to buy as a simple search can reveal tons of sites.
The first step is that I bake the castor oil in the sterile vial for 2 hours at around 350 degrees.
For formulation stainless steel kitchen measuring scoops are washed and dried, them triple rinsed and allowed to air dry with 70% IPA, then triple rinsed with DI water wrapped in foil and baked for an hour at 400 degrees F.
Once all ingredient are cool solvent is added first (BA/BB) then powder then hot castor oil is added and mixed with a glass rod previously cleaned and dried in foil as above, gloves are used sanitized with 70% IPA - once mixed and in solution the mix is transferred into a fresh sterile vial and baked at 300 degrees F for 60 minutes and then vented at the end with a needle for excess moisture and solvent vapor.
Basic solvent quantities are 1.5 % BA and around 10-15 % BB, hormone and end product doesn't exceed 250 mg ml.
Enanthate and tren are the easiest to make at lower solvent levels, Cyp prop and deca can go up to the higher ranges.
forget about drol dbol var strol in standard oil solvent recipes.
Let it fly flame or ?
Baked my gear from early on mex vet to UG and never had once single issue with sterility in the cases where it was high solvent level high dose those products were salvaged with diluting with USP oil and baking then transferring to sterile vials. always grew like a weed, many will tell you heat will destroy the hormone but it won't.
Castor oil is thick, but hormone solubility is excellent, and you won't be able to filter it no matter what, have tried many oils over the years and never really cared for grapeseed, sunflower, MCT , ethyl oleate, sesame or cotton seed.
Not getting into recipes cause there are tons of powder calculator sites around for oil powder solvent .
I use USP castor oil, and Sterile vials and USP solvents, please don't ask me to buy as a simple search can reveal tons of sites.
The first step is that I bake the castor oil in the sterile vial for 2 hours at around 350 degrees.
For formulation stainless steel kitchen measuring scoops are washed and dried, them triple rinsed and allowed to air dry with 70% IPA, then triple rinsed with DI water wrapped in foil and baked for an hour at 400 degrees F.
Once all ingredient are cool solvent is added first (BA/BB) then powder then hot castor oil is added and mixed with a glass rod previously cleaned and dried in foil as above, gloves are used sanitized with 70% IPA - once mixed and in solution the mix is transferred into a fresh sterile vial and baked at 300 degrees F for 60 minutes and then vented at the end with a needle for excess moisture and solvent vapor.
Basic solvent quantities are 1.5 % BA and around 10-15 % BB, hormone and end product doesn't exceed 250 mg ml.
Enanthate and tren are the easiest to make at lower solvent levels, Cyp prop and deca can go up to the higher ranges.
forget about drol dbol var strol in standard oil solvent recipes.
Let it fly flame or ?
Baked my gear from early on mex vet to UG and never had once single issue with sterility in the cases where it was high solvent level high dose those products were salvaged with diluting with USP oil and baking then transferring to sterile vials. always grew like a weed, many will tell you heat will destroy the hormone but it won't.
Castor oil is thick, but hormone solubility is excellent, and you won't be able to filter it no matter what, have tried many oils over the years and never really cared for grapeseed, sunflower, MCT , ethyl oleate, sesame or cotton seed.
Last edited: