AnaSCI - Fitness Evolved

Buy Needles and Syringes with NO PRESCRIPTION   Synthetek Muscle Building And Fat Loss Products   Cheap Pure Supplements

©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2019

   
  Synthetek Syntherol  
   
   
   
Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products


User CP FAQ Members List Calendar New Posts Quick Links Log Out

AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved


        
        
        
        
        

Automatic Translations (Powered by Yandex):
Albanian Belarusian Catalan Czech Danish Dutch English Estonian Finnish French German Greek Hungarian Italian Latvian Lithuanian Macedonian Norwegian Portuguese Russian Slovak Slovenian Spanish Swedish Turkish Ukrainian

Go Back Ā  Anabolic Steroids Discussion and Bodybuilding Forum > Anabolic Science Section > Anabolic Steroid Conversions

Reply
 
Thread Tools Display Modes
Tren A Wont Stop Chrystalizing
Old
  (#1)
Smack
Registered User
 
Offline
Posts: 27
Join Date: Apr 2014
Tren A Wont Stop Chrystalizing - 04-09-2014, 12:43 PM

So initially the Tren kept re-chrystalizing even heated in hot water (not boiling but bubbles forming on sides of container) and I was sent a replacement Tren A.

Well it's happening again every time even when heating and vigorously shaking... Any suggestions?

Thanks
   
Reply With Quote
Old
  (#2)
Sully
AnaSCI VET / Donating Member
 
Sully's Avatar
 
Offline
Posts: 3,298
Join Date: Dec 2012
04-09-2014, 12:47 PM

Just heat it up so it goes back into solution before you draw and inject. Shouldn't really be a problem.


GearPro Rep
[email protected]


It is the mark of an educated mind to be able to entertain a thought without accepting it- Aristotle
   
Reply With Quote
Old
  (#3)
Smack
Registered User
 
Offline
Posts: 27
Join Date: Apr 2014
04-09-2014, 02:09 PM

Quote:
Originally Posted by Lil' Sully View Post
Just heat it up so it goes back into solution before you draw and inject. Shouldn't really be a problem.
Thats what I've been doing but even when heated the chrystals dont fully dissolve.
   
Reply With Quote
Old
  (#4)
Sully
AnaSCI VET / Donating Member
 
Sully's Avatar
 
Offline
Posts: 3,298
Join Date: Dec 2012
04-09-2014, 02:48 PM

Ok, that changes the story. If you want to, you could try cutting it with some more oil and lowering the effective mg/ml of the end solution. Or it might just need a little more BB as a solvent to help it stay in solution.


GearPro Rep
[email protected]


It is the mark of an educated mind to be able to entertain a thought without accepting it- Aristotle
   
Reply With Quote
Old
  (#5)
Smack
Registered User
 
Offline
Posts: 27
Join Date: Apr 2014
04-09-2014, 02:50 PM

Quote:
Originally Posted by Lil' Sully View Post
Ok, that changes the story. If you want to, you could try cutting it with some more oil and lowering the effective mg/ml of the end solution. Or it might just need a little more BB as a solvent to help it stay in solution.
Thank you, I'll try that asap.
   
Reply With Quote
Old
  (#6)
Ironbuilt
Banned
 
Offline
Posts: 8,353
Join Date: Nov 2012
Location: Mūnich , Germany
04-09-2014, 03:31 PM

Prob cooked the chems right out of it making crystals harder .
   
Reply With Quote
Old
  (#7)
Enigmatic707
AnaSCI VET
 
Enigmatic707's Avatar
 
Offline
Posts: 2,752
Join Date: Feb 2013
04-09-2014, 05:46 PM

Quote:
Originally Posted by ironbuilt View Post
prob cooked the chems right out of it making crystals harder .

x2
   
Reply With Quote
Old
  (#8)
Smack
Registered User
 
Offline
Posts: 27
Join Date: Apr 2014
04-09-2014, 09:26 PM

Quote:
Originally Posted by Ironbuilt View Post
Prob cooked the chems right out of it making crystals harder .
I did by heating it in water or you meant the sponsor (I didnt brew it)?

Anyway, it was fine after adding a bit more oil...
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:03 AM.


Copyright © 2003-2019 AnaSCI.org. All rights reserved.