AnaSCI - Fitness Evolved

Buy Needles and Syringes with NO PRESCRIPTION   Synthetek Muscle Building And Fat Loss Products   Cheap Pure Supplements

©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2019

   
  Synthetek Syntherol  
   
   
   
Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products   Largest Selection of Bodybuilding Products


User CP FAQ Members List Calendar New Posts Quick Links Log Out

AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved  AnaSCI Fitness Evolved


        
        
        
        
        

Automatic Translations (Powered by Yandex):
Albanian Belarusian Catalan Czech Danish Dutch English Estonian Finnish French German Greek Hungarian Italian Latvian Lithuanian Macedonian Norwegian Portuguese Russian Slovak Slovenian Spanish Swedish Turkish Ukrainian

Go Back   Anabolic Steroids Discussion and Bodybuilding Forum > Anabolic Science Section > Anabolic Science Forum

Reply
 
Thread Tools Display Modes
been testing glute injections, getting ready
Old
  (#1)
mr.nitrofish
Registered User
 
mr.nitrofish's Avatar
 
Offline
Posts: 873
Join Date: May 2005
been testing glute injections, getting ready - 05-12-2005, 06:01 AM

well I have a bunch of 1/2" 28 gauge pins around for insulan for my diabetic cat. anyway I decided to poke myself with a new one just to see what I could expect. well it wasn't so bad, virtually painless. I sure hope I got the balls to do a 1 1/2" 22 gauge.

one question? should I peirce quick like a dart or slow and steady? does all 1 1/2" need to be in or just most of it?

im not looking forward to this, but no pain, no gain right
   
Reply With Quote
Old
  (#2)
imdaman1
AnaSCI VET
 
imdaman1's Avatar
 
Offline
Posts: 1,695
Join Date: Mar 2004
Location: USA
05-12-2005, 07:15 AM

Quote:
Originally Posted by mr.nitrofish
well I have a bunch of 1/2" 28 gauge pins around for insulan for my diabetic cat. anyway I decided to poke myself with a new one just to see what I could expect. well it wasn't so bad, virtually painless. I sure hope I got the balls to do a 1 1/2" 22 gauge.

one question? should I peirce quick like a dart or slow and steady? does all 1 1/2" need to be in or just most of it?

im not looking forward to this, but no pain, no gain right
You'll want to go in fairly slow so that you are able to stop and pull out in the event that you hit something such as a nerve or a bone.

To answer your second question - you don't want to bury the entire pin all the way up to the plastic coupling - you just want to get close to it. Leave 1/16" - 1/8" of the pin sticking out while injecting.

When injecting glutes, you can completely stabilize your hand and arm (eliminate the shakes) by doing this:

-while standing, back up near a wall
-twist your body slightly
-rest your injecting hand and forearm lightly against the wall
-make sure your leg and glute are relaxed and your weight is resting on the opposite leg
-hold the pin in the "ready" position
-slowly push your glute back into the pin, penetrating and then reaching the desired depth
-inject the meds with your plunger-finger resting against the wall
-pull your glute off and away from the pin


daman :wackit:
   
Reply With Quote
Old
  (#3)
mojo
Registered User
 
mojo's Avatar
 
Offline
Posts: 172
Join Date: Feb 2005
05-12-2005, 08:54 AM

injecting in the shoulder, quad, bi, tri, etc. you only need to go in about an inch (unless you have a lot of bf) but in the cheek I would go with the 1.5 inch most of the way to get through the fat.
   
Reply With Quote
Old
  (#4)
ORACLE
Perfection Personifide
 
ORACLE's Avatar
 
Offline
Posts: 3,069
Join Date: Dec 2004
Location: Tx
05-12-2005, 10:18 AM

Quote:
Originally Posted by mr.nitrofish
well it wasn't so bad, virtually painless. I sure hope I got the balls to do a 1 1/2" 22 gauge.
Try and get some 23 gauge if you can. I've done smaller number gauge sizes (remember smaller the number bigger the pin) and those tend to sting a little bit more while injecting. I use 25g now but i shoot in my quads.
   
Reply With Quote
Old
  (#5)
KILLA
Banned
 
KILLA's Avatar
 
Offline
Posts: 401
Join Date: Feb 2005
05-12-2005, 10:17 PM

Quote:
Originally Posted by mr.nitrofish
well I have a bunch of 1/2" 28 gauge pins around for insulan for my diabetic cat. anyway I decided to poke myself with a new one just to see what I could expect. well it wasn't so bad, virtually painless. I sure hope I got the balls to do a 1 1/2" 22 gauge.

one question? should I peirce quick like a dart or slow and steady? does all 1 1/2" need to be in or just most of it?

im not looking forward to this, but no pain, no gain right
I use 22g and they are fine for me. I just go slow when inserting, while darting very lightly. It will feel like it is jammed up, but after a few light jabs, it will continue on.
   
Reply With Quote
Old
  (#6)
HigherStandard
Registered User
 
HigherStandard's Avatar
 
Offline
Posts: 110
Join Date: Aug 2004
05-12-2005, 11:29 PM

I use 25 gauge in the quads now also. It feels the same as the 23 to me but it makes me feel better knowing that its a smaller pin. Its all psychological.
   
Reply With Quote
Old
  (#7)
pincrusher
Guest
 
Posts: n/a
05-13-2005, 08:25 AM

pin size will also have a little to do with the maker of your products. some manufacturers use slightly thicker oils which are harder to push through smaller sized pinz. i always try the smallest size i can comfortably get to flow without to much restriction because the harder i have to push on the plunger to get it to start flowing, the more likely it will be that i move the pin around while it is stuck in my body, which will cause the site to hurt more when im done.
   
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:00 AM.


Copyright © 2003-2019 AnaSCI.org. All rights reserved.