Buy Needles and Syringes with NO PRESCRIPTION Synthetek Muscle Building And Fat Loss Products Cheap Pure Supplements
©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2020

The Original Euro Supplier The Original Euro Supplier The Original Euro Supplier
Largest Selection of Bodybuilding Products Largest Selection of Bodybuilding Products Largest Selection of Bodybuilding Products


AnaSCI Fitness EvolvedAnaSCI Fitness EvolvedAnaSCI Fitness EvolvedAnaSCI Fitness EvolvedAnaSCI Fitness Evolved

Search results

  1. M

    Winny in oil recipe

    Has anyone made Winny in oil using the basic BA an BB solvents? I have made some using guaiacol but I want to try an experiment. I am certain I can heat some MCT or GSO hot enough to dissolve the winny without damaging it. My question is will BB hold it? I am only looking to make mg/mL max. I...
  2. M

    Zapcaps Way to Slow

    I recently purchased some whatman Zapcap .22 bottle top filters. I didn't change anything in my recipe for test E 2%BA, 20%BB, GSO for the carrier and the zapcpas are way to slow. It was literally a drop per second maybe. I have used Nalgene bottle top .22 and it has a much better rate. I use...
  3. M

    Best Way to Combine Powders

    When combining raw orals with a filler to cap what is everyone using ? I have seen the mortar and pestle but combining 20g of dbol, drol, or var by hand with those is a pain in the ass. I was taught to do geometric dilution by simply putting using a gallon size bag and shake, rotate, and mash...
  4. M

    Injectable With a Short Acting Ester and Oral

    Would it be possible to hold a low dose short ester steroid (prop/acetate,base) with an injectable oral ? I know popping an oral might be just as easy but say a home-brew cutting stack I could maker my boys that had 75mg Tren acetate with 25mg Anavar or 25mg Winny. Even something with Test bas...
  5. M

    Changing the order of brewing steps

    I am thinking of changing two steps when I brew. I have done about a dozen or so batches. No problems except the other thread about cyp crashing. I always go in this order: 1- Mix powder with correct ratio of solvents in beaker (usually 2%ba/18%bb lately been 2%ba/20%bb after the crash) 2- Mix...
  6. M

    Capping and tablet press

    Has anyone ordered a larger cap making machine. The ones off of amazon go from 100 caps to 400. There are also tablet presses that can be manual or hand crank. My question is has anyone purchased anything like this without any hassle of registering ? I am leaning towards staying away from a...
  7. M

    Crashing Into a Gel

    Made 200ml cyp@ 250mg/ml. Used the same recipe and supplier I have been for a while 2% BA and 18%BB. Put 30ml into a seperat vial for personnel use and its holding just fine. The bigger vial is starting have a sludge type gel at the bottom. Wondering if I need to heat the oil and add another 4ml...
  8. M

    Oil temperature

    After my last batch of masteron crashed. All my new batches I heat the oil in the microwave for about 30-45 seconds before mixing with the powder/solvent mixture. It clears and little clumps and makes the solution clear before filtering. Just curious as to when the oil is to hot for then...
  9. M

    Mold in my batch ?

    I recently brewed two batches. I did masteron 200ml 100mg/ml and test prop 200ml 100mg/ml. I used the same recipe for both 2%BA/18%ba. Both bottles were washed with 91% alcohol and baked in a 350 degree oven for 2 hours covered in foil. I used a Nalgene bottle top filter .22. The powder...
Top Bottom