©ALL CONTENT OF THIS WEBSITE IS COPYRIGHTED AND CANNOT BE REPRODUCED WITHOUT THE ADMINISTRATORS CONSENT 2003-2020



Test Enan Conversion (Pics)

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
By: 956Vette

This will make test enan at 250mg/ml

Things needed:
A few syringes min 3ml ea(5-10ml preferred)
A few needles 18-23g
Alcohol wipes or another way to help ensure sterility
2 sterile 10ml vials (must be identical)
1ml benzyl alcohol (BA)
1 .22-.44 pore size sterile syringe filter
2.5 grams testosterone enanthate powder (typically a paste at room temp)
11ml sterile oil
pen/marker that will write on glass
accurate scale
some water or preferably rubbing alcohol
 

Attachments

  • 1111.jpg
    1111.jpg
    28.1 KB · Views: 138

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
1-remove rubber stopper from 1 sterile vial by cutting the aluminum cap, use good scissors, nail clippers, metal shears, wire cutters etc…. once the metal cap is removed the rubber stopper will come off easily.
 

Attachments

  • 2222.jpg
    2222.jpg
    30 KB · Views: 139

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
2-fill the vial you modified with exactly 6ml of water or rubbing alcohol. Precisely mark the top level of the water/rubbing alcohol using the pen/marker, by writing on the glass vial.
 

Attachments

  • 333.jpg
    333.jpg
    30.4 KB · Views: 139

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
5-remove the water or rubbing alcohol from the vial and make sure it is COMPLETELY dry, try your best to not get any junk in the vial, let the water/rubbing alcohol evaporate, you may speed the drying process by placing it into a warm oven.

6-use the scale to measure exactly 2.5 grams of enanthate powder.
 

Attachments

  • 6666.jpg
    6666.jpg
    45.2 KB · Views: 139

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
8-using a clean needle and syringe: add .5ml BA to the enanthate powder and allow to dissolve completely.

9-Usually some low supplemental heat is required to dissolve it completely.
 

Attachments

  • 9999.jpg
    9999.jpg
    36.3 KB · Views: 139

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
10-add oil until you reach the level you previously marked off as the 6ml mark with the pen/marker.
 

Attachments

  • 100000.jpg
    100000.jpg
    28.5 KB · Views: 137

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
11-stir, or shake, or use low heat to ensure things mix properly.

12-using a fresh syringe and needle: while the oil enanthate mix is still warm, sterile filter it into the non modified(sealed) sterile vial. Use an alcohol wipe on the rubber stopper prior to penetrating it with the fresh needle. also place an extra needle through the rubber stopper to releive air presure.

13-place the modified and the non modified vials directly side by side.
 

Attachments

  • 1200.jpg
    1200.jpg
    27.7 KB · Views: 139

powders101

AnaSCI VET
Sep 21, 2007
1,556
0
0
The LAB
14-add more sterile oil through the sterile filter, into the sterile vial, until the oil level in the non-modified vial matches the 10ml mark you have made on the modified vial earlier. (this will be about 4ml usually) The purpose of this is to ensure complete purging of the enanthate /oil mix from the sterile filter, so a minimum amount is wasted.
 

Attachments

  • 1300.jpg
    1300.jpg
    35.8 KB · Views: 138

Collinb

Registered User
Sep 29, 2012
717
0
0
For the syringe filters, would you be able to use that with more than one vial? Like if you have 40ml of a substance, and 10 ml syringe, would you be able to draw out 10 use the filter to put into one vial, redraw and use the same filter in the next syringe?
 

vintagemuscle

AnaSCI VIP
Sep 24, 2003
81
0
0
For the syringe filters, would you be able to use that with more than one vial? Like if you have 40ml of a substance, and 10 ml syringe, would you be able to draw out 10 use the filter to put into one vial, redraw and use the same filter in the next syringe?

40ml should easily be handled by the one syringe filter.
 

Collinb

Registered User
Sep 29, 2012
717
0
0
Alright cool, what do you think would be the limit of one syringe filter? Going to have a go at home brewing soon just wanna make sure
 

Rfagazzi

New member
Oct 25, 2012
16
0
0
I've gotten as much as 160mls. I probably could've gotten more, but I got tired of pushing......
 

Collinb

Registered User
Sep 29, 2012
717
0
0
And should you avoid pushing two different oils through the same filter?
 

Rfagazzi

New member
Oct 25, 2012
16
0
0
I've done before in a pinch, it's not a big deal. Especially if your pushing the traditional 2cc's of carrier oil at the end. Either way you'll be fine. What little is in the filter shouldnt do anything. Even if the filter was loaded up, all you'll do is have a hint of the previous gear in the first bottle. However, if your going from test base with Guaiacol, to test-e, and it's for some bud's or whoever, then no, don't mix. Nobody wants their test-e smelling like ass!